0Fɛɛrɛ

ESP32 C3 0.42 inch LCD Development Board RISC-V WiFi Bluetooth Arduino/Micropython

4.9

★★★★★

111

$7.99 /$9.75

*Name:
*Email:
*Phone:
*Quantity:
*Content:
Attachment:

Supports JPG, JPEG, PNG, PDF, EXCEL, WORD, RAR, ZIP, 7z formats

$4.00 /$9.75

Sɔn sisan Panieri la sɛbɛ

Kredi kaati

Ka sɛn sɔgɔsɔgɔninjɛ

Sɔnni hɔrɔn

Sɔnni hɔrɔn o sɔnni bɛɛ la

Ka taa cogo

Ka taa hɔrɔn $9.9 kɔnɔ

Ka segin cogo

Sɔnni segin bɛ se ka sɔrɔ 40 don kɔnɔ Sɔnni yɛlɛman tɛ segin Sɔnniw minnu bɛ sɔn ni kaati hɔrɔn, olu tɛ segin

Sɔnni Hɔrɔn

I ni ce Roymall, i ka sɔnniw siti. An bɛ i ka dɛmɛ fɛɛrɛ. O sɔnni hɔrɔn bɛ kɛ i ka sɔnni kɛnɛ kan.

Ka Taa Cogo

An bɛ sɔnniw taa i ka so la 2 don kɔnɔ. Kɛnɛ cɛsiri bɛ se ka kɛ 5-7 don kɔnɔ.

1. Ka Segin Cogo

Sɔnniw bɛ segin 40 don kɔnɔ. Sɔnni yɛlɛman tɛ segin.

2.Ka Sɛn Segin

I bɛ sɛn sɔrɔ segin kɔnɔ.

Feature:

ESP32-C3 is a low-cost microcontroller from Espressif that supports 2.4 GHz Wi-Fi and Bluetoothu00ae Low Energy ( Bluetooth 5 (LE)).Use RISC V as the core.There"s a minimum number of pins on this chip, it"s specifically designed to be low cost and for simpler projects than ESP32-Sx or ESP32 classics with their large number of GPIO. Think of it more as an intended replacement to the ESP8266 than to the ESP32! It has built-inUSB-to-Serial, but not native USB - it cannot act as a keyboard or disk drive. The chip used here has 4MB of Flash memory, 400 KB of SRAM.

The ESP32-C3 integrates a rich set of peripherals, ranging from UART, I2C, I2S, remote control peripheral, LED PWM controller, general DMA controller, TWAI controller, USB Serial/JTAG controller, temperature sensor, and ADC. It also includes SPI, Dual SPI, and Quad SPI interfaces. There is no DAC or native capacitive touch.

With its state-of-the-art power and RF performance, this SoC is an ideal choice for a wide variety of application scenarios relating to the Internet of Things (IoT), wearable electronics, and smart homes.

Features:

based ESP32-C3FH4 WIFI & Bluetooth LE RISC-V Single-Core CPU

Type-C USB

4MB Flash

11x IO

1x1.0-4P connector(GND,3V3,SDA(GPIO5),SCL(GPIO6))

1x RGB(GPIO2)

1x LED(3.3V Power Supply)

1x Reset button(CHIP_EN,great for restarting your program or entering the ROM bootloader)

1x Boot button(GPIO9,entering the ROM bootloader or for user input)

Compatible with MicroPython, Arduinoand ESP-IDF

3.3V Regulator with 500mA peak output