Eachine ET1 STEM Upgrade Hit & Miss Gas Engine Stirling High Performance Engine Model Combustion Engine Collection Metal Toy
266
Direct purchase from the factory 
Ka sɛn sɔgɔsɔgɔninjɛ
Sɔnni hɔrɔn
Ka taa cogo
Ka segin cogoSɔnni Hɔrɔn
I ni ce Roymall, i ka sɔnniw siti. An bɛ i ka dɛmɛ fɛɛrɛ. O sɔnni hɔrɔn bɛ kɛ i ka sɔnni kɛnɛ kan.Ka Taa Cogo
An bɛ sɔnniw taa i ka so la 2 don kɔnɔ. Kɛnɛ cɛsiri bɛ se ka kɛ 5-7 don kɔnɔ.1. Ka Segin Cogo
Sɔnniw bɛ segin 40 don kɔnɔ. Sɔnni yɛlɛman tɛ segin.2.Ka Sɛn Segin
I bɛ sɛn sɔrɔ segin kɔnɔ.
Description:Brand: Eachine Item No.:Eachine ET1Item Name: Full Metal Hit & Miss Gas EngineColor: SliverMaterial: Aluminium AlloyWeight: About 2.2kg(Engine+Wooden Base)Size Of Engine: 180*125*75mm(L*W*H)Size Of Wooden Base: 180*66*50mm(L*W*H)Cylinder Diameter: 22mmLtinerary: 20mmVoltage: 3.5VFuel: ZIPPOOil or GasolineThe best tappet clearance: 0.5mmWeight: 1610gRevolutions Per minute:1200rmp
Spare Parts:For Rubber Ring
Engine Startup Steps:1. Open the bottom of base to check the wiring of the engine, connect the fuel tank piep, and install 3 AA batteries.2.Fill the fuel tank with gasoline(95#). When the filling is completed, make sure there"s no air in the oil pipe.3.On the right side of the engine(installation of the flying hammer position), slowly turn conterclockwise by hand to buy more than one turn.Its role can make the mixed gasoline fully enter the cylinder.4.Turn on the power switch and turn the flywheel to start the engine counterclockwise on the right side of the engine(installing the flying hammer position)
Precautions:1.If the ignition device is normal and the cylinder is under normal compression, if the machine still does not start normally, it"s very likely that the carburetor needle should be adjusted.2.Screw the screw on the top of the carburetor, then loosen 1/4 turn, start the flywheel. This can be done several times to make the mixing ratio od gasonline and air re ach the normal working mix ratio.
Note:1.Due to the different display and different light, the picture may not reflect the actual color of the item. Thanks for your understanding.
Spare Parts:For Rubber Ring
Engine Startup Steps:1. Open the bottom of base to check the wiring of the engine, connect the fuel tank piep, and install 3 AA batteries.2.Fill the fuel tank with gasoline(95#). When the filling is completed, make sure there"s no air in the oil pipe.3.On the right side of the engine(installation of the flying hammer position), slowly turn conterclockwise by hand to buy more than one turn.Its role can make the mixed gasoline fully enter the cylinder.4.Turn on the power switch and turn the flywheel to start the engine counterclockwise on the right side of the engine(installing the flying hammer position)
Precautions:1.If the ignition device is normal and the cylinder is under normal compression, if the machine still does not start normally, it"s very likely that the carburetor needle should be adjusted.2.Screw the screw on the top of the carburetor, then loosen 1/4 turn, start the flywheel. This can be done several times to make the mixing ratio od gasonline and air re ach the normal working mix ratio.
Note:1.Due to the different display and different light, the picture may not reflect the actual color of the item. Thanks for your understanding.
2.Please allow little differs due to manual measurement.3.Kids should be accompanied by adult. 4.Kids under 8 are not recommended to play.5.Please be carful when you add the fuel.6.An O-ring, which is not so airtight and can be started better
Package Included:1 X Eachine Hit & Miss Gas Engine (With Base)
